Tips

Shark Rocket HV301 Hose Replacement

Posted on by Mr Choes
22
Dec

WRITTEN BY: supportmymoto.com STAFF

Introduction

The hose of the Shark Rocket HV301 could should be changed if a gap has been worn into it. This will trigger weak suction and to your vacuum to not function correctly. If so, observe this information to switch the hose in your HV301. This information may additionally be used to disconnect your hose to take away a blockage.

  • Step 1

    Hose

    Place the base of the vacuum face down so the roller brush is facing you.Locate the five screws and remove the screws using a Phillips #1 screwdriver.You may want to disconnect the base from the stick of the vacuum to make it easier to move around.

    • Place the bottom of the vacuum face down so the curler brush is dealing with you.

    • Find the 5 screws and take away the screws utilizing a Phillips #1 screwdriver.

    • You could need to disconnect the bottom from the stick of the vacuum to make it simpler to maneuver round.

    Edit

  • Step 2

    Locate and remove the two small wheels below the roller brush by prying with a plastic prying tool.This may require some force.

    • Find and take away the 2 small wheels under the curler brush by prying with a plastic prying software.

    • This will likely require some drive.

    Edit

  • Step 3

    Locate and twist the three plastic screws to the unlock position with a quarter or flathead screwdriver.Pull up on the plate covering the roller brush and remove it.Pull up on the plate covering the roller brush and remove it.

    • Find and twist the three plastic screws to the unlock place with 1 / 4 or flathead screwdriver.

    • Pull up on the plate overlaying the curler brush and take away it.

    Edit

  • Step 4

    Turn the vacuum over so the roller brush is on the ground.Grab the vacuum on both sides of the hose and pull up to remove the top of the vacuum halfway.Grab the vacuum on both sides of the hose and pull up to remove the top of the vacuum halfway.

    • Flip the vacuum over so the curler brush is on the bottom.

    • Seize the vacuum on each side of the hose and pull as much as take away the highest of the vacuum midway.

    Edit

  • Step 5

    Gently pinch head of cable and pull upwards until upper casing disconnects from vacuum and proceed with removing upper casing.Return the vacuum to its original position with the roller brush facing you.Locate the screw to the right of the vacuum hose, close to the right wheel, and remove the screw with a Phillips #2 screwdriver.

    • Gently pinch head of cable and pull upwards till higher casing disconnects from vacuum and proceed with eradicating higher casing.

    • Return the vacuum to its unique place with the curler brush dealing with you.

    • Find the screw to the precise of the vacuum hose, near the precise wheel, and take away the screw with a Phillips #2 screwdriver.

    Edit

  • Step 6

    Pull on the dark gray end of the hose that attaches to the roller brush chamber to remove the hose from the base.This may require some force.Twist the hose out of the chamber that attaches the stick to the base.

    • Pull on the darkish grey finish of the hose that attaches to the curler brush chamber to take away the hose from the bottom.

    • This will likely require some drive.

    • Twist the hose out of the chamber that attaches the persist with the bottom.

    Edit

    • 55 Feedback

    Nice directions, now the place do I get the alternative hose. I can not seem to discover one anyplace, please inform be the place to look

    Kay Fisher –

    Reply

    Rob the hose from the arduous flooring attachment, you most likely don’t use it as at low velocity the comb head is superior on arduous flooring.

    Suzannne Scheans –

    NOTE : Please do not copy - https://supportmymoto.com

    Related posts:

    1. How to screenshot on macbook?
    2. How to fix controller drift ps4 fast?
    3. How to Fix the PS3 Controller Won’t Turn on at All Problem
    4. How to Fix the Microsoft FC 100 DLL Missing File?
    See also  Solution to Windows Update error 0x80040B0B
    Mr Choes

    Leave a Reply

    Situs Judi Slot Online Terpercaya

    Link Slot Gacor

    Slot Anti Rungkat

    Slot Gacor Maxwin